genie garage door starts to close then goes back up

When you try to close the door from the remote or wall unit it closes then you hear a click from around the motor unit and it goes back up. You can determine that it is your spring that is causing your door to stop opening all the way by disconnecting the cord from the opener and manually lifting it.

Genie Garage Door Opener Troubleshooting How To Guide The Indoor Haven

Check the Control Buttons.

. Your garage doors logic board is the brain of your garage door opener. This button is to prevent the door from opening or closing using the hand-held remote. It happens randomly on and off After some Google searches some common causes are - low remote battery - close limit set too close or far - safety sensors not aimed properly or something in the way.

1 There is an adjustment that sends a signal to the opener that it has traveled to the closed position. Verify if there isnt a block between them. Check if the limits are properly set.

They need to have a clear line-of-sight between them in order for the door to work properly. When the door touches the wooden board it should reverse to a fully open position within two seconds and the opener light will start flashing red as the door reverses. It goes partway down reverses direction and goes back up again.

When the garage door opens about halfway or 5 feet from the ground and stops the up limit switch needs to be adjusted. This brain can wear out in time so you could need a replacement. If there is such an issue you can see one of the sensor lights blinking.

Open the garage door and watch it closely as it opens. That could be the issue needs to be adjusted. When the logic board wears out it can cause your garage door to close then open and vice versa without explanation.

15 yr old Genie chain drive the door closes all the way to the ground then starts going up again. If the wires appear to be in good shape next look at the control button mounted near your side entry door. There are safety sensors at the bottom of your garage door.

That needs to be adjusted. If your garage door keeps going back up after youve closed it the most common reason is because. This is almost always the result of a dirty.

12K views View upvotes Related Answer. Endplay is caused by a loose or improperly installed shaft bearing kit. If anything enters the beam even briefly the door opens again.

Check if the Safe-T-Beams red LED light is flashing. Get Logic Board Replacement. Up to 25 cash back I have a Genie model 3062 garage door opener.

Ensure the motor shaft is tightened enough so that there is not too much endplay in the shaft. Once the door is up all the way its resting on the horizontal parts of the track and the resistance of the motor to turning because it is low geared should prevent it coming back down. This infrared sensor passes a beam horizontally across the opening.

Make sure ONLY the safe-t-beams that came with this garage door opener are installed. Your Logic Board Needs Replaced. This is because interference with the invisible beam helps the sensors communicate.

By Wade Shaddy Updated December 19 2018 You push the button to close the garage door. Safety sensors are the electronic eyes near the base of the door track on both sides. If it is old or dirty the button may stick.

Garage door starts down then STOPS and goes back up OR Safe-T-Beam System malfunction. If it is heavy to lift then it is probably the cause of the problem in the opening mechanism. Genie Garage door problem - open after close.

Then look to see if the rollers are in working order. Press the wall control button to close the garage door. If it is a NEW installation check the postion of the door arm.

The symptom of this is a garage door that is in constant motion opening fully then immediately descending only to start the same cycle again. A garage door that stops and goes back up is usually due to malfunctioning infrared sensors. In this case we recommend that you call a professional to address the issue.

Once it slides down does it go back up and stop in the correct place if it doesnt maybe the gear or gear shaft on the motor is stripped. If you see that the button is activated you should disengage it. Malfunctioning sensors can be caused by a blockage dirty eyes loose wires or just bad sensors in general.

Most wall controls will have a light indicating if the lock-out button is on. Misaligned or blocked sensors can make your garage door fail to close. Adjust the limits as needed.

2 There is an adjustment that sends a signal when it thinks it has hit an Obstruction. First you should check the safety sensors. Remove the wooden board from the doorway and press the wall control button to close the garage door.

The motor shaft moves back and forth through the motor more than 116th of an inch during operation it could lead to the door traveling only a short distance before reversing. To determine if this is the issue press the garage door button on the garage wall. The safety sensors are blocked.

The cause for your Genie garage door going up but not down is attributed to a problem stemming from the sensors rollers or limit switch.

Garage Door Troubleshooting Guides Geniedoor Com

Genie Garage Door Opener Troubleshooting The Genie Company

Genie 0 5 Hp Chain Drive Garage Door Opener In The Garage Door Openers Department At Lowes Com

Genie Garage Door Opener Troubleshooting The Genie Company

How To Troubleshoot A Genie Opener Creative Door

Common Problems With Genie Garage Door Openers List Of 7 Problems

Genie Garage Door Opener How To Troubleshooting Guide Nels Garage

Genie Garage Door Opener Opens But Does Not Close Youtube

Genie Silentmax Connect Garage Door Opener Review Pcmag

Reviews For Genie Signature Series 2 Hpc Screw Drive Wi Fi Enabled Smart Home Garage Door Opener 3 Button Remotes And Wall Console Pg 1 The Home Depot